Successstory-page-banner3.jpg

Terminology


ACCU-TRAK

ACCU-TRAK continuously measures the level of ground mineralisation while the detector’s coil is swept in search of targets. Any changes in mineralisation, which can occur quite quickly, are analysed and the Ground Balance level automatically adjusted.

ACCU-TRAK ensures the detector is always correctly ground balanced and operating at maximum depth and sensitivity at all times with minimum effort.

Illustration of Minelab's Accu-track metal detection technology

Back to Top ↑

Alkaline Battery

Alkaline batteries are non-rechargeable batteries. They are available in common battery sizes such as AA, C & D and have a voltage of 1.5 volts per cell. These are the most commonly available battery.

Back to Top ↑

All metal

All metal refers to operating a metal detector without any metals being masked or discriminated. All metals will be detected regardless of ferrous or conductive properties.

Back to Top ↑

Amplifier

An Amplifier is a device or electronic circuit that increases amplitude (strength) of an electrical signal. The signal can be either an audio signal (sound) or a radio signal (electromagnetic).

Back to Top ↑

Analogue

Analogue refers to a method of transmitting and receiving data between electronic devices or within an electronic circuit. Analogue signals contain information in their amplitude (i.e. 2.83 volts) at a point in time or over a period of time. (Also see “Digital”)

AnalogueSignal(sinewave).gif

Back to Top ↑

Auto tune

Auto tune is a metal detector feature that shifts the detector’s operating channel to reduce the effect of environmental noise. If an environmental noise source is operating at, or producing, harmonic frequencies that match the detector’s operating channel the detector becomes susceptible to falsing. By shifting the detector’s operating channel up or down the detector can avoid being affected by environmental noise. (Also see “Noise Cancel”)

Back to Top ↑

Broad Band Spectrum (BBS)

BBS (Broad Band Spectrum) simultaneously transmits, receives and analyses a broad band of multiple frequencies to deliver substantial detection depth, high sensitivity and accurate discrimination for a wide range of targets types.

This broad band of frequencies provides the detector’s electronics with more information about a target and the surrounding environment than is possible with single frequency technologies. The detector carries out advanced signal processing of these frequencies resulting in improved target identification accuracy and increased depth. This process also significantly reduces false signals from ground minerals, even in harsh and variable conditions, such as salt water beaches.

Back to Top ↑

CO

CO is an abbreviation that refers to conductivity on the Smartfind display found on the Explorer SE and E-TRAC.

Back to Top ↑

Coin, jewellery & relic hunting

Coin, jewellery & relic hunting involves detecting for coins, jewellery & relics as opposed to gold prospecting. Coin, jewellery & relic hunting metal detectors have different performance characteristics to gold prospecting detectors. Coin, jewellery & relic hunting detectors have good discrimination and can be programmed to reject specific types of metal objects or junk. They also generally come with a display pod, so a user can determine what a target might be before digging.

 

Back to Top ↑

Concentric coil

A Concentric coil has an inner circle and an outer circle wire winding. The search pattern is cone shaped and can be useful for accurately pinpointing targets. Concentric coils require more sweep overlap for thorough ground coverage. They are also noisier in highly mineralised ground and therefore might not be the best choice for gold prospecting.

Illustration of a metal detectors Concentric Coil

Back to Top ↑

Conductivity

Conductivity.jpg

Conductivity refers to how well a target allows electrical current to flow through it. In other words a highly conductive target has low electrical resistance and therefore allows current to flow more easily. Conversely a target with low conductivity has high electrical resistance and does not allow current to flow easily. (Also see ”Time constant”)

Back to Top ↑

Continuous wave

Continuous wave is a type of metal detecting technology. Continuous wave metal detectors create an electromagnetic field that is applied to the ground in a continuous sine wave.

Back to Top ↑

Control box

Metal detector control box

The control box encloses the electronic circuitry of the detector, that generates the Tx (transmit) signals sent by the search coil and processes the Rx (receive) signals detected by the search coil.

Back to Top ↑

Current

Current is the flow of electrical charge and is measured in Amperes (A or Amps). Current measurements are common on batteries and power supplies (i.e. AA NiMH battery: 2600 mAh, DC power supply: 1.5 A). Current is also induced into targets by the electromagnetic field produced by metal detectors, these are called eddy currents.  (Also see “Voltage”)

Back to Top ↑

Depth

Depth in metal detecting terms refers to how deep a target is buried. A metal detector that can achieve greater depth is able to detect deep targets. Minelab’s E-TRAC, X-TERRA and Explorer SE also have graphical depth indicators.

Back to Top ↑

Detectorist

A detectorist is a person who regularly uses metal detectors professionally or as a hobby.

Back to Top ↑

Digital

Digital refers to a method of transmitting and receiving data between electronic devises or within an electronic circuit. Digital signals (or data) use only two states, high or low and generally conform to a counting method called binary. Electronic circuits that process digital signals have many advantages over analogue circuits, including; less susceptible to noise and interference, able to process more information, able to filter signals using less electronic components, are lighter and cheaper.

DigitalSignal69.gif

Back to Top ↑

Discrimination

Notch discrimination.jpg

Discrimination is a metal detector’s ability to identify buried targets based on conductive and/or ferrous properties. By accurately identifying a buried target you can decide to dig it up or consider it as junk and continue searching. Minelab detectors produce target identification (Target ID) numbers and/or Target Tones to indicate the type of target that has been detected.

There are four main types of discrimination in Minelab detectors:

  1. Variable discrimination – The simplest type of discrimination which uses a control knob to adjust the level of discrimination.
  2. Iron Mask/Iron Reject – Used mostly with gold prospecting detectors to ignore iron junk.
  3. Notch discrimination – Allows specific target types to be accepted or rejected.
  4. Smartfind – The most advanced form of discrimination. Target IDs are plotted based on both ferrous and conductive properties on a two dimensional (2D) display. Individual segments or larger areas of the display can be shaded to reject unwanted targets.

Back to Top ↑

Discrimination pattern

A Discrimination pattern is a graphical representation of accepted and rejected targets based on ferrous and conductive properties. Targets with properties that appear in the shaded section are masked and targets with properties that appear in the non-shaded area are accepted. Discrimination patterns are used on Minelab’s X-TERRA series (one dimensional) as well as Explorer and E-TRAC with the two dimensional Smartfind discrimination display. (Also see “Discrimination”)

Back to Top ↑

Double-D coil (DD)

Illustration of a metal detectors Double-D Coil

A Double-D coil has two overlapping wire windings in the shape of two D’s. The benefits of a Double-D coil are stability (especially in heavily mineralised ground), good depth, sensitivity and a very thorough search pattern requiring less overlap.

When used with GPX detectors, Double-D coils (unlike Monoloop coils) are able to discriminate between ferrous and non-ferrous targets when Iron Reject is activated. They are also more stable when used on wet salt beach sand and in electrically noisy environments.

When used with X-TERRA detectors, Double-D coils perform quieter than Concentric coils in mineralised ground and are therefore well suited for gold prospecting.

Back to Top ↑

Dual Voltage Technology (DVT)

DVT (Dual Voltage Technology) is Minelab’s advanced Pulse Induction technology that uses pulses with two voltage levels to further enhance MPS. The two voltage levels work in combination with the different time period pulses transmitted by MPS to increase the amount of power transmitted into the ground. DVT also allows more of the ground signal to be removed, further increasing detection depth and sensitivity. This achieves ultimate depth in extremely mineralised ground.

DVT.gif

Back to Top ↑

Eddy currents

Eddy currents are tiny electrical currents that are induced into targets when a metal detector’s electromagnetic field is present. These eddy currents then generate an electromagnetic field around the target which can be detected by a metal detector.

Illustration of how a metal detector operates

Back to Top ↑

Electromagnetic field

Electromagenetic Field.jpg

An electromagnetic field is a physical field produced by electrically charged metal objects. This refers to both the transmit field from the detector’s search coil and the receive field from a target. The electromagnetic field illustration shows the transmit field from the coil in blue and the receive field from the target in yellow.

Back to Top ↑

Environmental noise

Environmental noise comes from power lines, underground cables, radar, other detectors or climatic conditions like thunder storms that produce electrical signals or noise that can interfere with a metal detector’s operation.

Back to Top ↑

Falsing

Falsing occurs when a metal detector gives a detection response to electrical noise, ground noise or bumping.

Back to Top ↑

FE

FE is an abbreviation that refers to a target’s ferrous properties on the Smartfind display found on the Explorer SE Pro and E-TRAC.

Back to Top ↑

Ferrous (Fe)

Ferrous.jpg

Ferrous objects/targets contain iron and therefore are attracted to a magnet, e.g. horse shoes, nails, tin cans. The ferrous illustration shows a ferrous nail being attracted to a magnet. Many natural and man-made objects contain iron, most of these are junk targets, however some can be valuable relics.

Back to Top ↑

Frequency

The frequency of a metal detector is one of the main characteristics that determines how well targets can be detected. Generally, a single frequency detector that transmits at a high frequency will be more sensitive to small targets and a single frequency detector that transmits at low frequencies will give more depth on large targets. Minelab’s single frequency technologies are VLF and VFLEX. Minelab’s revolutionary BBS, FBS and MPS technologies transmit multiple frequencies and are therefore simultaneously sensitive to small and deep large targets.

OneCompleteCycle.gif

For example if a signal repeats itself 10 times every second the signal’s frequency is 10 Hz.

10CompleteCycles.gif

The frequency that a metal detector operates at (transmitted by the search coil) affects its performance, as a rule of thumb, the lower the frequency, the deeper it can penetrate the ground. At low frequencies however, sensitivity to small low conductive targets is reduced. The higher the frequency, the higher the sensitivity to small targets, but will not penetrate as deeply.

In general, gold detectors operate at higher frequencies (to find small nuggets), while coin and treasure detectors work at lower frequencies for deeper penetration. The exception to this is MPS type metal detectors that are sensitive and deep seeking simultaneously.

Back to Top ↑

Frequency domain

Frequency domain refers to the viewing or analysis of signals with reference to frequency, rather than time. (Also see “Time domain”)

TimeDomain.gif

Back to Top ↑

Full Band Spectrum (FBS)

FBS (Full Band Spectrum) simultaneously transmits, receives and analyses a full band of multiple frequencies. This provides the detector’s electronics with even more information about a target and the surrounding environment than is possible with single frequency or BBS technology. This has a number of advantages, including:

  • High sensitivity across a wide range of target types and sizes, so you only have to cover the ground once.
  • Automatic sensitivity and ground compensation, so maximum depth is achieved even in mineralised ground, including salt water beaches.
  • Extremely accurate multi-channel signal conversion to precisely separate target signals from ground signals for maximum detection depth and high resolution target identification.
  • Smartfind two dimensional discrimination, giving you maximum target information, so that targets can be discriminated by both ferrous and conductive properties simultaneously.
Full Band Spectrum (FBS) metal detection technology

Back to Top ↑

Gold prospecting

Gold prospecting is the activity of searching for new gold. Gold prospecting metal detectors have different performance characteristics to Coin, jewellery & relic hunting metal detectors. Gold prospecting metal detectors have superior ground balancing abilities to operate in highly mineralised ground and can detect targets at greater depth.

Back to Top ↑

Ground balance

Ground Balance is a variable setting that increases detection depth in mineralised ground. This ground may contain salts, such as in wet beach sand or fine iron particles, such as in red earth. These minerals respond to a detector’s transmit field in a similar way that a target does. Due to the much larger mass of the ground compared to a buried target, the effect of mineralisation can easily mask small targets. To correct this the Ground Balance setting removes the responding ground signals, so you clearly hear target signals and are not distracted by ground noise.

There are three main types of Ground Balance:

  1. Manual Ground Balance – Manually adjust the Ground Balance setting, so the minimum amount of ground signal is heard.
  2. Automatic Ground Balance – The detector automatically determines the best Ground Balance setting. This is quick, simple and more accurate than a manually set Ground Balance
  3. Tracking Ground Balance – The detector continuously adjusts the Ground Balance setting while detecting. This ensures that the Ground Balance setting is always correct.

Minelab detectors use exclusive advanced technologies for superior ground balancing capabilities that cannot be matched by any other detectors.

Back to Top ↑

Ground mineralisation

Ground mineralisation.jpg

Ground Mineralisation refers to the naturally occurring minerals in the ground that affect a metal detector’s performance. There are two main types of ground mineralisation, one is due to iron particles and can be identified by its red colouration. The other is due to salt, such as salt water beaches. Iron particle mineralisation causes the ground to become magnetic and salt mineralisation causes the ground to become conductive. Both forms of ground mineralisation can produce false signals that mask targets. The ground mineralisation illustration shows minerals in the ground producing a response to the metal detector’s electromagnetic field.

Back to Top ↑

Ground noise

Ground noise is the false signalling caused by a metal detector that is not ground balanced to the soil. The ground noise occurs when the unbalanced detector’s search coil is swept across ground that varies in mineralisation, soil type, rocks or has dips and holes. 

Illustration of how ground noise is generated when metal detecting

Back to Top ↑

Ground tracking

Ground tracking refers to the ability of the detector to track changes in ground mineralisation and automatically adjust the ground balance to suit. This ensures perfect ground balance and full detection depth, eliminating the need for the operator to stop and manually adjust the detector as ground conditions change.

Back to Top ↑

Halo effect

Halo effect occurs after a target has remained undisturbed in the ground for a considerable amount of time. As the target breaks down or rusts the soil immediately around it becomes highly mineralised. A detector will see this area of high mineralisation and give a detection response indicating that the target is larger than it really is.

Back to Top ↑

Harmonic frequencies (harmonics)

Harmonic frequencies are components of a signal or wave that are multiples of the fundamental frequency. For example a 15 kHz signal will have harmonic frequencies at 30 kHz, 45 kHz, 60 kHz, 75 kHz and so on. These harmonic frequencies reduce in magnitude as they get further and further away from the fundamental frequency of 15 kHz. Harmonic frequencies are best viewed in the frequency domain.

HarmonicFrequencies.gif

Back to Top ↑

Hot rocks

Hot rocks are rocks that are mineralised differently to their surrounding ground. For example a highly mineralised rock buried in mildly mineralised ground would be considered to be a hot rock. However, a highly mineralised rock in an equally highly mineralised ground would not be considered to be a hot rock. (Also see "Ground mineralisation")

Illustration of hot rocks when metal detecting

Back to Top ↑

Iron Mask

Iron mask refers to operating a metal detector with iron masked or discriminated. Only non-ferrous metals containing little or no iron will be detected.

Back to Top ↑

Junk

Junk (or trash) refers to unwanted ferrous or non-ferrous metal targets. Nails, paperclips and wire are examples of ferrous junk and bottle tops, ring pulls and foil are examples of non-ferrous junk. Junk is often buried amongst valuable targets like coins. To solve this, Minelab has a range of metal detectors with the ability to ‘ discriminate’ whether a target is likely to be treasure or trash based on both ferrous and conductive properties.

Back to Top ↑

Lithium-ion battery (Li-ion battery)

Lithium-ion batteries are a new type of rechargeable battery that has advantages over older rechargeable battery technologies like nickel-metal hydride (NiMH), nickel cadmium (NiCd) and sealed lead acid (SLA). Lithium-ion batteries are lighter, have no memory effect and a low self discharge rate.

Back to Top ↑

Monoloop coil

Monoloop coils are a special style of coil for MPS technology detectors (SD & GPX Series). These coils have one winding of wire around the circumference of the coil, which is used to both transmit and receive. The signal pattern of the Monoloop coil is cone shaped, requiring more overlapping. In extremely heavily mineralised grounds they can be more difficult to ground balance, however they tend to provide slightly better depth than the Double-D coils.

Illustration of a metal detectors Monoloop Coil

Back to Top ↑

Multi period sensing (MPS)

MPS (Multi Period Sensing) is Minelab’s advanced Pulse Induction (PI) technology that transmits pulses of different time periods. MPS also samples the receive signal at multiple time periods allowing target signals and ground signals to be separated. This effectively removes the ground signal from even the most highly mineralised ground while still being sensitive to both small and deep gold. This achieves superior depth in extremely mineralised ground.

MPS.gif

Back to Top ↑

Multi-frequency

Multi-frequency is a type of metal detector technology that uses more than one frequency. Single frequency metal detectors can be limited due to their fixed frequency. This is because lower frequencies detect deeper into the ground, but higher frequencies detect smaller targets. By combining multiple frequencies into one detector, depth and sensitivity to small targets is achieved. (Also see “Broad Band Spectrum (BBS)” & “Full Band Spectrum (FBS)”)

Back to Top ↑

Nickel cadmium battery (NiCd)

Nickel cadmium batteries are rechargeable batteries. They are available in common battery sizes such as AA, C, and D, however at 1.2 volts they have a slightly lower cell voltage than alkaline and carbon zinc batteries. NiCds have high discharge current capabilities due to their low internal resistance, but suffer from memory effect and have a relatively high self discharge rate (will discharge themselves over about ten weeks).

Back to Top ↑

Nickel metal hydride battery (NiMH)

Nickel metal hydride batteries are rechargeable batteries, which have advantages over NiCd batteries. NiMH provide 1.2 volts per cell, but do not suffer from a memory effect and are capable of higher energy densities than NiCd batteries.

Noise Cancel

Noise Cancel is a metal detector feature that shifts a metal detector’s operating frequency or frequencies to reduce the effect of environmental electromagnetic noise, from sources such as power lines, cell phone towers and other metal detectors. (Also see “Auto tune”)

Back to Top ↑

Non-ferrous

Non-ferrous materials do not contain iron. Good targets include coins, gold rings and copper artefacts. Junk targets include bottle tops, pull tabs, and aluminium foil. (Also see "Ferrous")

Back to Top ↑

Notch filter discrimination

Notch filter discrimination discriminates a narrow group of metal objects based on their conductive and ferrous properties.

Back to Top ↑

Ohm

Ohm is a unit of measure of electrical resistance (symbol Ω). Resistance measurements are common on headphones and speakers. (Also see “Voltage” & “Current”)

Back to Top ↑

Period

Period is the time it takes for a wave or signal to complete one cycle. The period is also the inverse of the wave’s frequency. (i.e. period = 1/frequency)

Period.gif

Back to Top ↑

Pinpointing

Illustration of pinpointing when metal detecting

Pinpointing is the activity of narrowing down the location of a buried target. Many of Minelab’s detectors have a pinpointing mode that allows the user to determine the exact location of a target before digging. The process involves putting the detector into pinpoint mode and slowly sweeping the ground above the target to find the strongest response, then turning 90º and sweeping again to get an accurate target location. 

Back to Top ↑

Pulse Induction (PI)

Pulse Induction (PI) is a type of metal detecting technology. Pulse induction operates by sending short pulses of voltage to the metal detectors coil. These short pulses cause a magnetic field to be generated which quickly dissipates at the end of each pulse. Any metal targets that induce the magnetic field remain magnetised for a short time after the end of a pulse. The target’s decaying magnetism is then detected by the detector’s coil. (Also see “Multi period sensing (MPS)” & “Dual Voltage Technology (DVT)”)

Back to Top ↑

QuickMask

QuickMask is a feature available on Minelab’s E-TRAC. QuickMask allows a user to quickly edit and customise a discrimination pattern.

Back to Top ↑

Receive (Rx)

Receive is the process of collecting a signal or magnetic field by the metal detector’s search coil.

Back to Top ↑

Resistance

Resistance is the opposition to current flowing in an electrical conductor and is measured in Ohms(Ω).

Back to Top ↑

Sealed lead acid battery (SLA)

Sealed lead acid batteries are rechargeable batteries. They come in a wide variety of sizes and are most often packaged in 6 volt or 12 volt packs. SLA batteries have high discharge current capabilities due to their low internal resistance.

Back to Top ↑

Search Coil (loop)

Illustration of a metal detectors Search Coil

The search coil is the circular or elliptical plate that is swept above the ground during detecting. It transmits electromagnetic signals into the ground and receives the response. The word coil actually refers to the wire windings inside the housing, which can take different forms and shapes. For more information on the different types of coils see Concentric coil, Double-D coil and Monoloop coil.

Back to Top ↑

Sensitivity

Sensitivity refers to how responsive a metal detector is to small or deep targets.

Back to Top ↑

SETA

SETA (Smart Electronic Timing Alignment) is a highly complex method of matching the characteristics of individual Timings with continuous measurements from the surrounding electromagnetic environment, such as the earth’s magnetic field. This gives the advantage of improved detector performance through the complete removal of noise signals. The sensitivity across all Timings is increased, therefore SETA allows more gold to be found than any other metal detector technology.

SETA.gif

Back to Top ↑

Signal

Signal in metal detecting terms refers to both the transmitted magnetic field from the detectors search coil and the received magnetic field from a metal target.

Sine wave

A sine wave or sinusoid is the name of a waveform that mathematically corresponds to the sine function [y(t) = A•sin(ωt + θ)]. A pure electrical sine wave does not produce harmonic frequencies.

SineWave.gif

Back to Top ↑

Smartfind

Smartfind is Minelab’s unique two dimensional scale of discrimination. Smartfind graphically represents a target’s ferrous and conductive properties on the same display.

Smartfind is a feature of two Minelab metal detectors; E-TRAC and Explorer SE Pro.

E-TRAC Smartfind:
The horizontal axis rates the target on its size/conductivity (CO), ranging 1–50 from left to right. The vertical axis rates the extent of the target’s ferrous characteristics (FE), ranging 1–35 from top to bottom. A FE value of 1 represents low ferrous characteristics and a value of 35 represents high ferrous characteristics. Similarly, a CO value of 1 represents low conductivity and 50 represents high conductivity.

E-TRAC metal detector Smartfind display

Explorer SE Pro Smartfind:
The vertical axis rates the target on its size/conductivity (CO), ranging 0–31 from bottom to top. The horizontal axis rates the extent of the target’s ferrous characteristics (FE), ranging 0–31 from right to left. A FE value of 0 represents low ferrous characteristics and a value of 31 represents high ferrous characteristics. Similarly, a CO value of 0 represents low conductivity and 31 represents high conductivity.

Explorer metal detector Smartfind display

Back to Top ↑

Square Wave

A square wave is the name given to a waveform that has rapid transitions from one state to another. Square waves are used in electronics as clock signals, timing pulses and control signals. Square waves generate many harmonic frequencies.

SquareWave.gif

Back to Top ↑

Target

Target refers to any metal object that can be detected by a metal detector. A target can be either valuable, such as a coin or junk, such as a bottle top.

Back to Top ↑

Target ID

Target ID numbers and audio tones are produced by a metal detector to enable you to identify targets based on their conductive and/or ferrous properties.

Target Target ID
US Quarter 44
Australian $1 coin 32
Ring pull 12
Wedding ring 8
Long screw -4
Short screw -4
Paper clip -4

Back to Top ↑

Threshold

Threshold is the continuous sound used to listen for target signals. The Threshold will ‘blank’ to indicate the detection of a discriminated/rejected target.

Threshold.gif

Back to Top ↑

Time constant

Time constant is a measure of a target’s combined conductivity and inductance. A target with high conductivity (low resistance) and high inductance will have a long time constant (i.e. gold ingot). A target with low conductivity (high resistance) and low inductance will have a short time constant (i.e. fine jewellery). Minelab metal detectors are capable of detecting the full range of time constants.

Back to Top ↑

Time domain

Time domain refers to the viewing or analysis of signals with reference to time, rather than frequency. (Also see “Frequency domain.”)

TimeDomain.gif

Back to Top ↑

Timings

Timings refer to the digital switching rates that control the internal electronics of the detector. In the GPX series of detectors the timings generate a pulse train to create the transmit waveform. The same timings generate synchronised switching signals to control the receive electronics.

Selecting different timings and thus changing both the transmit waveform and synchronised receive switching signals have benefits for different ground types and targets. Minelab has created a range of different timings in the GPX series of detectors that achieve optimum depth, sensitivity and ground balancing across different detecting conditions. (Also see “Multi period sensing (MPS)”, “Dual Voltage Technology (DVT)” & “SETA”)

Back to Top ↑

Tone identification

Tone identification is similar to target ID numbers; however, instead of using displayed numbers different tones are associated to different target IDs.

Back to Top ↑

Transmit (Tx)

Transmit is the process of sending a signal or magnetic field from the metal detector’s search coil.

Back to Top ↑

Trashy ground

Trashy ground is ground that has high levels of junk.

Back to Top ↑

Universal Serial Bus (USB) port

A Universal Serial Bus is a type of computer data port. Minelab’s E-TRAC has a USB port that enables it to communicate with a PC to upload and download settings and discrimination patterns.

Back to Top ↑

VFLEX

VFLEX is Minelab’s metal detecting technology used in the X-TERRA range of detectors. VFLEX uses state of the art digital electronics to enhance standard single frequency detection technology. This has the advantage of providing dependable performance and improved immunity to outside interference. VFLEX technology also has an added advantage that changing the detector’s coil also automatically changes the detector’s operating frequency. This means that an X-TERRA detector can operate at different frequencies allowing the detector to be easily modified to suit different detecting conditions.

vflex.jpg

Back to Top ↑

VLF (Very low frequency)

VLF is a type of metal detecting technology. VLF metal detectors create an electromagnetic field that is applied to the ground in a continuous sine wave.

Back to Top ↑

Voltage

Voltage is electrical potential and is measured in volts (symbol v). Voltage measurements are common on batteries and power supplies (i.e. AA NiMH battery: 1.2 v, DC power supply: 12v). Voltage is used to energise a metal detector’s search coil, which in turn generates the electromagnetic field. (See also “Current” & “Resistance”)

Back to Top ↑

Website by Bridgehead ...Powered by WebTemplate